The bintec W1001n is a manageable access point with one radio module and fits perfectly for applications which require only one frequency band. The bintec W1001n provides the same software features as the products from the W Series.
The bintec W1001n offers three different modes of operation. You can operate the device as a stand-alone access point or manage it from a central bintec WLAN Controller. The W1001n can also function as a WLAN Controller itself (master access point) and manage up to six APs. The bintec WLAN Controller solution can be used in wireless networks with anywhere from 2 to 150 access points. The bintec WLAN Controller solution provides a scalable, end-to-end solution that lets you expand your network without migrating to a new technology. This flexibility protects your investments in existing infrastructures.
Clean lines and elegant design make this device an appealing choice for wall- or ceiling-mounting. It looks perfectly at home in high-end office spaces or hotels. Despite its handsome appearance, this access point also knows how to blend in. We`ve placed the antennas inside the housing, and you can turn off the LEDs to eliminate distractions.
The housing itself comes ready for wall mounting, eliminating the need for an additional wall-mount bracket. A bracket is available as an optional accessory for mounting the device on the ceiling. This ceiling-mount bracket also allows the device to be secured against theft by means of a Kensington lock. As an alternative to wall-or ceiling-mounting, you can also place the W1001n on a desktop thanks to the included rubber feet.
Whether you`re operating a standalone access point or using a WLAN Controller, you can take advantage of the optional HotSpot solution that allows you to provide controlled access to your network for guests - an ideal solution for hotels and restaurants.
The W1001n also supports handover and roaming. That means with a properly set up and surveyed wireless network managed by a bintec WLAN Controller, wireless devices enjoy seamless coverage throughout the network. And seamless coverage is a must if you are, for instance, implementing a VoWLAN (Voice over WLAN) solution or using wireless barcode scanners for logistics applications.
The W1001n gives you green IT right out of the box with its automatic energy-saving features. If no client is connected, these APs turn off any circuits not currently in use, downshifting to MIMO 1x1. The Gigabit Ethernet ports support the energy-saving 802.3az standard, ensuring only as much energy as needed is used.
In addition to its access point functionality, the device can also be used as a wireless LAN client to give Ethernet-ready devices such as printers access to the wireless network. In addition, these units can also function as a wireless bridge links in point-to-multipoint mode with up to eight links. The ability to use a single radio module simultaneously as an access point and to operate a bridge link master makes it particularly efficient to implement wireless backbones. In these two operating modes, it is not possible to also use the device as a WLAN Controller.
Operation ModesWLAN AP
WLAN Access Point stand-alone or WLAN Access Point managed by a WLAN Controller or WLAN Master-Access Point can control up to 5 additional AP
WLAN Bridge link Point-to-Point or Point-to-Multipoint
WLAN Client operation
Wireless LANWLAN standards
802.11n (Mimo 2x2); 802.11b; 802.11g; 802.11a; 802.11h
Frequency 2,4 GHz Indoor/Outdoor
2,4 GHz Indoor/Outdoor (2412-2484 MHz)
Frequency 5GHz Indoor
5 GHz Indoor (5150-5240 MHz)
2,4 GHz Operation: 802.11b only; 802.11g only, 802.11b/g/n mixed; 802.11b/g/n mixed long; 802.11b/g/b mixed short; 802.11b/g/n ; 802.11g/n; 802.11n only
5 GHz Operation: 821.1a only; 802.11a/n; 802.11n only
up to -95dBm without antenna gain
TX Power @ 2,4GHz
up to 16dBm without antenna gain
TX Power @ 5GHz
up to 16dBm without antenna gain
TX Power adjustable
5dBm, 8dBm, 11dBm, 14dBm, 17dBm, max.
Automatic or manually
Automatic Rate Selection
Number of spatial streams (802.11n)
1 or 2
Up to 16 SSID per radio with own MAC address for each SSID. Each SSID can assign to a VLAN to separate the traffic.
Open, WEP64 (40 Bit key), WEP128 (104 Bit key), WPA Personal, WPA Enterprise, WPA2 Personal, WPA2 Enterprise
IEEE802.11i authentication and security
802.1x/EAP-MD5, 802.1x/EAP-TLS, 802.1x/EAP-TTLS, 802.1x/EAP-PEAP, Key Management, PSK/TKIP Encryption, AES Encryption, 802.1x/EAP
Access control list (ACL)
MAC address filter for WLAN clients (white list) and dynamic and static blacklist. Black list function requires WLAN Controller
WIDS (Wireless Intrusion Detection System)
Rogue AP detection: detect foreign Aps, which try to sp out data via SSIDs by permanent background scanning. When the attack is detect a SNMP trap or a email alert can be send. This functionality requires WLAN Controller.
WIDS (Wireless Intrusion Detection System)
Neighbor AP detection: Detect AP in the neighborhood, which can reduce the performance at the own network. In case of detection a SNMP trap or a email alert can be send.This functionality requires WLAN Controller.
WIPS (Wireless Protection Detection System)
Rogue Client Detection: detection and protection detect conspicuous clients, which try to intrude or interfere the wireless network.In threat case blocking by dynamic black list. This functionality requires WLAN Controller.
Network separation at layer 2. For each SSID ist one VLAN ID possible. Static VLAN configuration according IEEE 802.1q, supports up to 32 VLANs.
Inter traffic blocking for public HotSpot (PHS) applications for preventing of communication WLAN client to WLAN client in a single radio cell
Optimizing the throughput when slow clients or clients there are far away are connected
Client load balancing
Avoid overloading of the AP in the case that many users are connected. Allow the movement of clients to other AP in case of high load.
Limitation of the number of clients
From 1to 250 clients. It could be useful to allow more than 32 clients with applications with low bandwidth requirement.
A maximum throughput can be defined for each client. Defineable or each SSID
TPC (Transmission Power Control): For 5 GHz, automatic TX power reduction according EN301893)
WMM 802.11e QoS
Data priority for TOS tagged data according 802.11e/WMM
WMM 802.11e Power Save
Supports WLAN Clients there supporting 802.11e power save and U-APSD
Seamless Roaming through IAPP (Inter Access Point Protocol) support according 802.11f useful for VoWLAN phones and for Wireless Barcode scanner.
Software Features for AP stand-alone operationCaptive portal function / HotSpot
Additional external RADIUS server or bintec HotSpot license required
NTP Client, NTP Server, manually
DHCP client, DHCP server, DHPC relay
IPsec, L2TP, PPTP, GRE
Software Features for WLAN Client operationFunctionallty
Layer 2,5 Bridge for connect several IP based device and one non-IP device to a wireless network.
Open, WEP64 (40 Bit key), WEP128 (104 Bit key), WPA Personal, WPA2 Personal
Selectable (no, slow, normal, fast, customized roaming). For fast moving clients (i.e. vehicles) to be archive a seamless roaming. This feature is realized by scanning the relevant channels in the background.
Show a list of available AP in the area
For one SSID, manually configuable or configuable by using the scanning function
Detailed information for each link (Uptime, Signal, Noise, Data rate, …)
Software Features for WLAN Bridge operationConfiguration
Applicable as Access-Point/Bridge-Link Master or as Bridge-Link Client
For Point-to-Point or for Point-to-Multipoint (up to 8) applications.
Detailed information for each link (Uptime, Signal, Noise, Data rate, ...)
Administration / ManagementHTTP/HTTPS
Web based configuration
Via Telnet, SSH, HTTP, HTTPS, SNMP
SNMP (v1, v2, v3), USM Model, VACM Views, SNMP Traps (v1, v2, v3) selectable, SNMP IP access list configurable
Complete Management according MIB-II, MIB 802.11, Enterprise-MIB
Support SSH V1.5 and SSH V2.0 for secure connection of terminal application
Backup/Restore to/from file
Optional encrypted backup file
Optional automatic backup via scheduler
WLAN Controller operation
Manageable with the bintec WLAN Controller according CAPWAP (DHCP option RFC1517)
Integrated WLAN controller for 5 additional bintec AP
Syslog Client with different level of the messages
Automatic eMail if any defined event occurs
Statistic information for all physical and logical interfaces
Detailed information about the radio, SSIDs, Bridge link, clients. For each link MAC address, IP address, TX packets, RX packets, signal for each antenna, Signal/Noise value, data rate.
WLAN History view
Show the performance values based on WLC, AP, SSID, Client level help to detect any bottlenecks
The following events are plan able: device reboot, activate/deactivate interfaces, activate/deactivate SSIDs, trigger of software update, trigger of configuration backup
One interface 10/100/1000 Mbps, autosensing, auto MDI/MDIX
One RJ-45 socket
Two integrated dual band antennas @2,4GHz peak gain 4 dBm @5GHz peak gain 3 dBm
9-12V/1A DC ; 100-240V AC wall adaptor with Euro plug or PoE according 802.3af or 802.3at (Wall adaptor and PoE injector not included)
Power Consumption max.
ca. 6,5 Watt
Power Consumption in networked standby mode
< 4,5 Watt
Approx. 15.9 cm x 14.5 cm x 4.3 cm (width x depth x height)
Temperature operating: 0°C to 40°C; storage: -10°C to 70°C; rel. Humidity 10 to 95% (non condensin)
Theft protection integrated, Kensington ® compatibel
Wall mounting integrated at the housing Rubber pad for desktop operation included Ceiling mounting unit as accessory available
Directive 2014/53/EU, 2011/65/EU, 2009/125/EU EN 60950-1; EN 62311; EN 301489-1; EN301489-17; EN 300 328; EN 301893; EN 50581)
bintec W Series / WO Series / WI Series
- Release 10.2. Rev. 4 Patch 1
- Release 10.2. Rev. 3
- Release 10.2. Rev. 2 Patch 2
- Release 10.2. Rev. 2 Patch 1
- Release 10.2. Rev. 2
- Release 10.1. Rev. 23 Patch 2
- Release 10.1. Rev. 23 Patch 1
- Release 10.1. Rev. 23
- Release 10.1. Rev. 21 Patch 3
- Release 10.1.10 Patch 7
- Release 10.1. Rev. 10 Patch 6
- Release 10.1. Rev. 10 Patch 3