This site requires cookies to work properly. Note that if you continue navigating our website, you indicate your consent to our use of cookies. More Information at the Data Protection Statement.

Spanish EnglishGerman



bintec W2022ac

MU-MIMO WLAN Access Point


  • 802.11ac access point with MU-MIMO technology
  • 867Mbps @ 5GHz and 400Mbps * @ 2.4GHz
  • Simultaneous operation in the 2.4 and 5 GHz band
  • Flexible management solutions
  • Easiest ceiling mounting on system ceilings
  • 5-year hardware warranty
  • Available December 2018





bintec W2022ac

802.11ac access point with MU-MIMO technology for the high-performance support of mobile devices.


The bintec W2022ac is an access point based on the latest 802.11ac standard and supports MU-MIMO (Multiple User MIMO). The MU-MIMO technology allows mobile devices (such as smartphones) that have only one antenna to use all the transmission streams of an access point. Compared to 802.11ac first-generation access points, which support only single-user MIMO (SU-MIMO), twice as many mobile devices can connect to the bintec W2022ac without sacrificing performance. This doubles the overall performance.

 

Together with the WLAN controller integrated in be.IP, commissioning becomes child's play. In larger installations, you have the choice between a local installed bintec WLAN controller solution and the bintec Cloud NetManager*. In addition, the bintec W2022ac is already prepared for the new bintec be.SDx solution.

 

The new ceiling mount is available as an accessory and allows mounting on suspended system ceilings without drilling and dowels or direct mounting on wood or concrete ceilings. For mounting on the wall, the optional ceiling mount is not necessary.

 

Five-year warranty on the hardware of the bintec W2022ac.

* In preparation

WLAN AP
WLAN Access Betrieb
WLAN Standards
802.11b; 802.11g; 802.11n (MIMO 2x2) 2.4 GHz
Receiver Sensitivity @ 2.4 GHz 802.11b
-97dBm
Receiver Sensitivity @ 2.4 GHz 802.11g
-92.5dBm
Receiver Sensitivity @ 2.4 GHz 802.11n 20/40 MHz
MCS0 -91,5dBm; MSC7 -73,5dBm
Tx Power @ 2.4 GHz 802.11b/g
1 Mbps 20dBm; 6Mbps 20dBm; 54Mbps 18 dBm without antenna gain
Tx Power @ 2,4 GHz 802.11n 20/40MHz (2 Streams)
MCS0 20dBm; MSC7 20dBm without antenna gain
Frequency bands 2.4 GHz indoor/outdoor (EU)
2.4 GHz Indoor/Outdoor (2412-2484 MHz) max. 100 mW EiRP (20dBm)
Data rates for 802.11b,g (2.4 GHz)
11, 5.5, 2 und 1 Mbps (DSSS modulation); 54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation)
Data rates for 802.11n, 20 MHz channel bandwidth
MCS0-15 allow up to 150 Mbps PHY rate at 20 MHz channel bandwidth, 2 streams, Short guard Intervall. Up to 200 Mbps (QAM-256) together with clients there support QAM-256.
Data rates for 802.11n, 40 MHz channel bandwidth
MCS0-15 allow up to 300 Mbps PHY rate at 40 MHz channel bandwidth, 2 streams, Short guard Intervall. Up to 400 Mbps (QAM-256) together with clients there support QAM-256.
Output power limitation
Adjustable
Output power @ 2.4 GHz
Max. 20dBm
Automatic Rate Selection (ARS)
Available
Transmission rate
Automatic
Number of spatial streams (802.11n)
1 or 2
Bandwidth (802.11n)
20 MHz / (40MHz with coexistence check under preparation)
Short guard interval (802.11n)
On/off switchable; increase of throughput by reduction of the guard intervals from 800ns to 400ns
DTIM Period
Adjustable
Extended Performance Feature
Beamforming, MRC (Maximum Ratio Combining), Block-Acknowlegde, STBC (Space Time Block Coding), LDPC (Low Density Parity Check
Multi SSID
Up to 8 service sets per radio module, with virtual access points and own MAC address per SSID
Broadcast SSID
On/off switchable
WLAN Standards
802.11ac/an; MU-MIMO 2x2; 20/40/80 MHz; 5 GHz
Receiver Sensitivity @ 5 GHz 802.11a/h
6 Mbps -90 dBm; 54 Mbps -73 dBm
Receiver Sensitivity @ 5 GHz 802.11n 20/40/80 MHz
MCS0 -89.5 dBm; MCS7 -72.5 dBm; MCS8 -68.5 dBm; MCS9 -64 dBm
Tx Power @ 5 GHz 802.11a/h
6 Mbps 20 dBm; 54 Mbps 17 dBm without antenna gain
Tx Power @ 5 GHz 802.11ac/n 20/40/80 MHz (2 chains)
MCS0 22 dBm; MCS7 19 dBm; MCS9 14 dBm without antenna gain
Frequency bands 5 GHz indoor (EU)
5 GHz indoor (5150-5350 MHz) max. 200 mW EiRP allowed.
Frequency bands 5 GHz outdoor (EU)
5 GHz outdoor (5470-5725 MHz) max. 1000 mW EiRP allowed.
Data rates for 802.11a,h (5 GHz)
54, 48, 36, 24, 18, 12, 9 and 6 Mbps (OFDM modulation)
Data rates for 802.11n, 20 MHz channel bandwidth
MCS0-15 allow up to 150 Mbps PHY rate at 20 MHz channel bandwidth, 2 streams, Short guard intervall
Data rates for 802.11n, 40 MHz channel bandwidth
MCS0-15 allow up to 300 Mbps PHY rate at 40 MHz channel bandwidth, 2 streams, Short guard intervall
Data rates for 802.11ac, 20 MHz channel bandwidth
Allow up to 173 Mbps PHY rate with two streams or up to 87 Mbps PHY with one stream.
Data rates for 802.11ac, 40 MHz channel bandwidth
Allow up to 400 Mbps PHY rate with two streams or up to 200 Mbps PHY with one stream.
Data rates for 802.11ac, 80 MHz channel bandwidth
Allow up to 867 Mbps PHY rate with two streams or up to 433 Mbps PHY with one stream
Output power limitation
Adjustable
Output power @ 5 GHz
Max. 23 dBm (200mW EiRP)
Automatic Rate Selection (ARS)
Available
Transmission rate
Automatic
Number of spatial streams (802.11ac/n)
1 or 2
Bandwidth (802.11n)
20/40 MHz
Bandwidth (802.11ac)
20/40/80 MHz
Short guard interval (802.11n)
On/off switchable; increase of throughput by reduction of the guard intervals from 800ns to 400ns
DTIM Period
Adjustable
Extended Performance Feature
Beamforming, MRC (Maximum Ratio Combining), Block-Acknowlegde, STBC (Space Time Block Coding), LDPC (Low Density Parity Check)
Multi SSID
Up to 8 service sets per radio module, with virtual access points and own MAC address per SSID.
Broadcast SSID
On/off switchable
WLAN security modes
WPA2 personal, WPA2 enterprise, WPA personal, WPA enterprise, Open
IEEE802.11i Authentisierung und Verschlüsselung
802.1x/EAP-MD5, 802.1x/EAP-TLS, 802.1x/EAP-TTLS, 802.1x/EAP-PEAP, key management, PSK/TKIP encryption, AES encryption, 802.1x/EAP
Multiple RADIUS for WPA/WPA2 Enterprise
Up to 8 different RADIUS servers can be configured and assigned to the individual SSIDs.
Access control list (ACL)
MAC address filter for WLAN clients (white list) and dynamic and static blacklist.
WIDS (Wireless Intrusion Detection System)
Rogue AP detection: Detect foreign APs there using the own SSID, by permanent background scanning. As a result, attack attempts can be detected in time. This functionality requires WLAN Controller or the Cloud NetManager.
WIPS (Wireless Intrusion Protection System)
Rogue Client Detection: detection and protection: detect conspicuous clients, which try to intrude or interfere the wireless network.In threat case blocking by dynamic black list. Requires the WLAN Controller or the Cloud NetManager
WIDS (Wireless Intrusion Detection System)
Neighbor AP Detection: detection of neighbor Aps with possible influence on performance of own network. By detected intrusion: SNMP trap or email alert. This functionality requires the WLAN Controller.
VLAN
Network segments on layer2 possible. Per SSID one VLAN ID available. Static VLAN configuration according IEEE 802.1q; up to 16 VLANs supported.
Inter cell repeating
Inter traffic blocking for public HotSpot applications for preventing of communication radio client to radio client in a single radio cell.
Performance Monitoring
Tracks performance values for the Access Point, the SSID anf for the dedicated, connected WLAN clients. This feature helps to analyze performance or to figure out bottlenecks. This feature requires a WLAN Controller or the Cloud NetManager.
Airtime Fairness
Prevent performance limitation by slower or distant clients, which block the network (under preparation).
Client Band Select
Shifting of clients to 5 GHz band
Client Management
Client overload protection (too many clients) and shifting of clients to other APs, if the threshold is reached.
Data rate trimming
Enhance the system performance by disable lower legacy data rates (under preparation).
Low RSSI threshold management
Clients with weak Signal (Sticky Clients) can disconnected automatically (under preparation). This improve the roaming behavoiur of the clients and enhance the system performance of the WLAN Network.
Roaming
Seamless roaming with IAPP (Inter Access Point Protocol), support according 802.11f
Broadcast SSID
Data prioritization for TOS data, 802.11e/WMM
WMM 802.11e power save
Support of active WLAN clients, which support 802.11e power save.
U-APSD
Unscheduled Automatic Power Save Delivery (under preparation). This functionality contributes significantly to raise battery life of Voice-over-WLAN end devices
Multicast Support
IGMP Snooping, Multicast to Unicast converting of WLAN data.
bintec HotSpot
Supported, Router as HotSpot Gateway required
Mimo 1x1 shift down
The radio modules switching automatic to Mimo 1x1 operation, when no client is connected
802.3az support
The ethernet interfaces reduce the power consumption automatically, in case that no device is connected. In the case of the usage of a short ethernet cable, the circuit reduce the transmit power.
LED Mode
The LEDs has three operation mode: Status, Flashing, Off
Graphical user interface
Web-based configuration, monitoring and maintenance via HTTP reachable. The user interface is identical with almost all bintec elmeg products
Configuration export and import
Load and save of configurations; save configuration optionally encrypted
Software Maintenance
Software updates free of charge until 2 years after EOS available. Update via file, HTTP or via direct access to the bintec elmeg upload Server.
Internal Log
Output via web-based configuration interface; filter: subsystem, level, message
Interfaces Monitoring
Statistic information of all physical and logical interfaces
WLAN Monitoring
Detailed displays for radio, VSS. Displayed are per link: MAC address, IP address, TX packets, RX packets, signal strength for each antenna, signal-to-noise ratio, data rate
Language support
German, English, Spanish
WLAN Controller functionality
Managed by a local WLAN Controller, works as WTP.
Discovery protocol
CAPWAP DHCP option according RFC1517 or by static WLC IP address
Background scanning
Background scanning (can be deactivated) for the detection of threads (WIDS) and for the detection of neighbor APs. The results are reported to the WLC.
Performance Monitoring
Sends the performance data of the Access Point, the SSIDs and for each associated WLAN client to the WLAN Controller. This features helps to analyze bottlenecks.
WLC based scheduler
Activate/Deactivate WLAN SSID; Software Update
Alerting
WLAN Controller based email and SNMP alerting when a AP is down, for new detected threads.
Supported Cloud Management Systems
Prepared for Cloud NetManager, Virtual Cloud NetManager, bintec be.SDx
Zero Touch Provisioning (ZTP)
Zero Touch Provisioning (ZTP) out of the box without customized pre-configuration
Background scanning
Background scanning (can be deactivated) for the detection of threads (WIDS) and for the detection of neighbor APs. The results are reported to the Cloud Management.
Performance Monitoring
Sends the performance data of the Access Point, the SSIDs and for each associated WLAN client to the Cloud Management. This features helps to analyze bottlenecks.
Cloud scheduler
Scheduled software update
Alerting
Cloud based email and SNMP alerting when a AP is down, for new detected threads.
Standards and certifications
Directive 2014/53/EU, 2011/65/EU, 2009/125/EU, EN 60950-1; EN 62311; EN 301489-1; EN301489-17; EN 300 328; EN 301893; EN 50581; EN 60601-1-2 (Medical devices - part 1-2)
LAN / WAN
2 x 10/100/1000 Mbps Ethernet twisted pair, autosensing, auto MDI/MDI-X
WLAN
One radio module IEEE 802.11bgn MIMO 2x2 and a second radio module IEEE 802.11ac/an MU-MIMO 2x2 allow simultaneous operation at 2.4 and 5 GHz.
Antenna
Integrated single band MIMO antenna array with two antenna elements for each radio; 2 dBm gain @ 2,4 GHz; 3 dBm gain @ 5 GHz.
Realtime clock
System time persists even at power failure for some hours.
Power supply
External wall power supply 230V / 12V DC, 1A, with high efficient switching power supply (The wall adaptor is a accessory and not include the shipment).
PoE
Power-over-Ethernet according IEEE 802.3af, compatible with 802.3at PoE injectors
Status LEDs
Status, Activity for WLAN1, WLAN2 and Ethernet, LEDs defeatable
Wall mounting
Integrate at the housing backplane
Ceiling mounting and theft protection
Accessorie required (5520000163) with integrate theft protection via Kensington® lock
Desktop operation
Integrated rubber pads
Dimensions
Approx. 190 mm x 190 mm x 38 mm (width x depth x height)
Weight
Approx. 505 g
Power consumption
max. 8.95 Watt
Environment
Temperature operating: 0°C to 40°C; storage: -10°C to 70°C; rel. humidity 10 to 95% (non condensing)
Warranty
5 years warranty for the hardware. Not for accessories like power adaptor, .. Online RMA procedure.
Documentation
Quick install guide in German and English languages is part of the delivery. Online help in German and English. Die complete user manual is available as download.
Content of delivery
bintec W2022ac; Quick install guide, security Information. Note: The power supply of the devices work via a Power Adapter which is available as accessory (5500002091) or via PoE.

bintec W2022ac Part number: 5510000422

Power supply 12V with EU socket Part number: 5500002091

Gigabit PoE Injector Part number: 5530000338

Ceiling mounting W2022ac Part number: 5520000163



Request Info
X